#DUAL STICK RANGER MANUAL#
#DUAL STICK RANGER FULL#
#DUAL STICK RANGER FREE#

To find diagrams and replacement part numbers, use the online parts catalog. Maintenance tips, procedures and specifications can be found in your Owner's Manual. Find a dealer near you with the Dealer Locator. Confirm the reset by tapping the red RESET button.įor more information, see your authorized Polaris Dealer. To reset the interval on a seven-button Ride Command display:ĥ. Programmable Service Interval on Seven-Button Ride Command Display Press either toggle button to cycle to the trip time option (TT). The trip time meter tracks the travel time during a specific trip. Press and hold either toggle button until the meter resets to zero. Press either toggle button to cycle to the desired trip meter option (T1 or T2).Ģ. The trip meter can be used to track to distance traveled during a specific trip or period of time. In the rider information center, you also can reset your trip meter and trip time meters. Press MODE to save and exit to the settings menu. Press MODE to reset the existing value and exit or press either toggle button to change the value. Press either toggle button to cycle to the “Service Hours” option. Press and hold the MODE button to enter the settings menu.Ģ. Use the following procedure to reset or change the service interval.ġ.

#DUAL STICK RANGER MANUAL#

Refer to the Periodic Maintenance Chart in your Owner’s Manual for recommended service intervals. When this feature is enabled, it provides a convenient reminder to perform routine maintenance. The wrench icon will flash for about 10 seconds when the counter reaches zero and each time the key is turned on thereafter until the counter is reset. As hours of engine operation increase, the counter decreases. The service interval counter is programmed to 25 hours at the factory. Resetting Your Rider Information Center's Service Hours CounterĪmong the features on your RANGER’s Rider Information Center is the service hours counter. When finished, reinstall the oil fill cap, oil dipstick and lock the lever.Ģ1. Add the recommended oil as necessary to bring the oil level within the SAFE range on the dipstick. Remove the dipstick and check the oil level.ġ9. Make certain the dipstick is inserted all the way into the dipstick tube to keep the depth of the dipstick consistent.ġ8. Reinstall the dipstick and push it into place. Remove the dipstick and wipe it dry with a clean cloth.ġ7.

Wait at least 15 seconds before removing the dipstick.ġ6. Stop the engine and inspect it for oil leaks. Start the engine and allow it to idle for 30 seconds.ġ5. Verify the transmission is still in PARK.ġ4. The oil capacity is 2.5 quarts (2.4 liters).ġ3. Fill the engine with the recommended engine oil. Torque the drain plug to 12 ft-lbs (16 Nm).ġ2. Reinstall the engine crankcase drain plug with the 6mm Allen socket. The sealing washer is part number 5812232.ġ1.

#DUAL STICK RANGER FREE#

The sealing surface on the drain plug should be clean and free of burrs, nicks or scratches. Replace the sealing washer on the drain plug. Both oil change kits include the filter.ġ0. Turn the oil filter until the filter O-ring contacts the sealing surface and then turn an additional 3/4 turn. Check to make sure the O-ring is in good condition. Lubricate the O-ring on the new oil filter with a film of fresh engine oil. Using a clean dry cloth, clean the filter sealing surface on the engine crankcase.ĩ. Using the 2.5-inch (64mm) oil filter wrench, turn the oil filter (2) counterclockwise to remove it.Ĩ.

Pull up on the cargo box release lever to tilt the box.ħ. Always remove all cargo from the cargo box before lifting the box to access the engine.Ħ. Place a drain pan under the engine crankcase and remove the drain plug with a 6mm Allen socket. Do not allow hot engine oil to come into contact with skin, as serious burns may result.Ĥ. Use caution when performing this procedure. Clean the area around the crankcase drain plug. Stop the engine and allow it to cool down.ģ.

Position the vehicle on a level surface and place the transmission in PARK.Ģ. The Extreme Duty Oil Change Kit is part number 2879324.ġ.

#DUAL STICK RANGER FULL#

The PS-4 Full Synthetic PS-4 Oil Change Kit is part number 2879323. Access the drain plug through the skid plate access hole located directly under the crankcase. The crankcase drain plug is located on the bottom of the crankcase. Access the oil dipstick and oil fill cap by tilting the rear cargo box. When changing the oil on your Polaris RANGER XP 1000 or RANGER CREW XP 1000, always wear safety glasses and nitrile gloves. Always check and change the oil at the intervals outlined in the Periodic Maintenance Chart in your Owner's Manual. To learn more about tools, read the Tools and Fasteners Guide.

Dual stick ranger